Single Face Corrugated Board Rewinder

1400–2200

Working Width (mm)

60

Mechanical Speed (m/min)

1400

Max. Rewinding Diameter (mm)

Chat on WhatsApp
Single facer corrugated board rewinder machine page hero

The AGICO PAPER single-face corrugated board rewinder is a corrugated board machine. This equipment rewinds single-face corrugated board produced by a single facer into rolls. It is mainly used in 2-ply corrugated board production lines and semi-automatic corrugator lines. It is installed after the single facer and belongs to the rewinding station in the production line.

AGICO PAPER's corrugated board rewinder is used in applications where single face corrugated board needs to be wound into rolls. Unlike equipment that cuts board into specified sizes, the rewinder mainly handles continuous board winding and does not cut the board into individual sheets.

Finished corrugated paper rolls

If a corrugated box plant needs to produce rolls of single face corrugated board, it can use a single face corrugated board rewinder for this purpose. The corrugated board rolls can be supplied to other corrugated board equipment for further production. The factory can choose a suitable rewinder configuration based on the production line's working width, production speed, and actual winding requirements.

Advantages of Rewinder for Single Face Board

Depending on the selected model and configuration, AGICO PAPER can supply a single face corrugated board rewinder equipped with a variable speed control system, an automatic tension control system, and a hydraulic loading and unloading device. These configurations are used to adjust rewinding speed, control roll tension, and assist with roll loading and unloading.

Match Production Speed

This corrugated board rewinder has a PLC control system, a touchscreen, and a variable frequency drive. Operators can adjust the rewinder production speed based on the production speed of the single facer. This keeps the rewinding process in line with the previous production process and reduces production waiting caused by speed differences.

Maintain Roll Quality

To reduce board damage caused by excessive tension during board rewinding, we use an automatic tension control system. This system helps solve production problems such as loose or uneven rolls caused by insufficient tension. It also helps keep the rolls neat and tight.

Reduce Manual Operation

The machine uses hydraulic lifting support arms and a hydraulic roll clamping device to assist with shaft lifting and roll clamping. This can reduce the workload of operators when handling heavy rolls. At the same time, the automatic length counter records the rewinding length and gives an alarm when the set length is reached, making it easier for operators to handle the rolls in time.

Not Just a Single Machine: A Complete Corrugator Line

AGICO PAPER provides not only a single face board rewinder, but also a complete board rewinding solution for small carton factories.

The rewinder can work with a single facer and a mill roll stand to form a semi-automatic corrugated board production line. This line is mainly used to produce single face corrugated board.

2-ply corrugated cardboard production line in factory

Main Configurations of Corrugated Board Rewinder

single face corrugated board rewinder overview
single-face corrugated board roll

PLC Control System

Our rewinder for single face board uses a PLC control system with a touchscreen for monitoring. Variable frequency control adjusts the rewinding speed. Operators can monitor machine operation through the control interface and adjust the speed according to production requirements.

Automatic Tension Control System

AGICO PAPER's rewinder has an automatic tension control system. It supports both manual and automatic tension adjustment. Operators can adjust the rewinding tension based on the board type and actual rewinding conditions.

Hydraulic Loading and Unloading Mechanism

The roll support arms use a hydraulic lifting structure, and a hydraulic device clamps the shafts. This system assists with shaft lifting and clamping during roll loading and unloading.

Rewinding Shafts

We supply two square shafts as standard. An inflatable shaft is also available as an option. Customers can choose the shaft type according to their production requirements.

Specifications of the Single Face Board Rewinder Machine

Swipe to view all specifications →

Parameter

Specification

Machine Type

Single Face Corrugated Board Rewinder

Available Working Widths

1400 / 1600 / 1800 / 2000 / 2200 mm

Mechanical Speed

60 m/min

Economic Speed

40–50 m/min

Maximum Rewinding Diameter

1400 mm

Minimum Rewinding Diameter

500 mm

Note: The above parameters are for reference only. For specific information, please contact AGICO PAPER.

Discuss Your Rewinding Requirements

Share your working width, line speed and required roll diameter.

Chat on WhatsApp

Working Process of the Single Face Corrugated Board Rewinder

As a basic corrugated board rewinding machine, the rewinder is mainly used to wind the single face corrugated board continuously produced by the single facer into rolls. When the board reaches the set length, the machine cuts the board and completes the current roll. After unloading the roll, the machine can start winding the next roll.

single face corrugated board rewinder working process
  1. Corrugated Board Infeed

    The single face corrugated board enters the corrugated rewinder from the single facer machine and is prepared for continuous feeding for subsequent winding.

  2. Corrugated Board Feeding

    Corrugated board passes through the guide rollers and enters the rewinding area. It moves smoothly during feeding, ready for the rewinding process.

  3. Corrugated Board Rewinding

    The rewinding shaft rotates continuously and gradually winds the single face corrugated board into a roll.

  4. Finished Roll Unloading

    When the board reaches the set length, the machine cuts the continuous board and completes the current roll. The finished roll is then unloaded, ready for the next winding cycle.

Operation Cautions

  1. Pre-Operation Inspection

    Before starting the machine, check all machine components, electrical connections, switches, screws, and safety devices. Make sure the machine is properly lubricated. Run the machine without a load to check that it works normally before operation.

  2. Authorized Operators

    The single face corrugated board rewinder should be operated only by trained operators. Unauthorized persons should not use the machine. During operation, do not place tools or other objects on the machine.

  3. Operating Safety

    When the machine is running, never put your hands near the rewinding shaft or feeding rollers. Operators should follow the machine's safety operating procedures.

Why choose AGICO PAPER

Related Equipment Supply

AGICO PAPER provides single face corrugated board rewinders, single facers, 2-ply and multi-ply corrugated board production lines, and related machines and spare parts. Customers can purchase a rewinder separately. They can also purchase a single facer and a matching rewinder, or choose a complete corrugated board production line. These options meet different equipment purchasing needs.

AGICO PAPER corrugated machiney factory

Customized Equipment Solutions

Different single facers require different rewinder sizes and specifications. AGICO PAPER can customize the rewinder's working width, maximum rewinding diameter, and rewinding speed according to customer requirements. Customers can provide the working width and production speed of their existing single facer. They can also provide the required roll diameter and specifications. We use this information to determine the rewinder's parameters and configuration.

Corrugated machine installion

International Delivery Experience

We export our products to more than 30 countries and regions, including the United States, Spain, Austria, Italy, Germany, Poland, Russia, and the Netherlands. We understand the requirements for international logistics and customs declarations. We also have experience preparing English technical documents and export packaging for corrugated machinery. We can provide on-site installation services for overseas customers or guide them through equipment installation by video.

AGICO PAPER corrugated equipment shipment

FAQ

  1. Can the corrugated board rewinder work with my existing single facer?

    Yes. We can recommend a suitable rewinder based on your existing single facer. Please provide its brand, model, working width, and production speed. You can also send us machine photos or technical specifications.

  2. Does the single face corrugated rewinder cut board into individual sheets?

    No. The rewinder is mainly used to wind continuous single face corrugated board into rolls. It cuts the board when it reaches the preset length to separate the finished roll, but it does not cut the board into individual sheets of a specified size.

  3. What information is needed to get a corrugated board rewinder quote?

    Please provide the working width, production speed, and corrugated board flutes for a single facer. Please also provide the required roll diameter. If you are setting up a new production line, please provide the production requirements for the entire line.

  4. How do I choose the right single face corrugated board rewinding width?

    The rewinder working width should match the maximum board width produced by your single facer. This ensures that the rewinder can handle the board from your existing production. If you purchase a complete production line, the working widths of the single facer and rewinder should also match.

PLAN YOUR EQUIPMENT

Tell us what you want to produce

Complete the form with your contact details and equipment requirements. Use the message field to share the points below.

  1. Equipment you need

    A complete production line, an individual machine, or an upgrade to your existing equipment.

  2. Your product specifications

    Board ply and flute type, working width, box dimensions, or printing and converting requirements, where known.

  3. Output and project details

    Your target production capacity, installation country, and any workshop space or project requirements.

Not sure which machine to choose? Describe your product and what you want to achieve. Share the details you know to get started.

Your equipment requirements

All four fields are required.Your inquiry will be submitted securely to our company inquiry system. Privacy information.

Your equipment requirements

Name, email and message are required. Phone / WhatsApp is optional.Your inquiry will be submitted securely to our company inquiry system. Privacy information.